PT02 · STOICHIOMETRY
2A:1B vs. 1A:1B Mix Ratio & 350 RPM Discipline
Exact Part A resin & Part B hardener stoichiometry, 3-minute submerged helical mix, and immediate ribbon dump rule.
SOLIDS98–99% HIGH SOLIDS
DRY TO TOUCH2 HOURS @ 72°F
LIGHT FOOT4–6 HOURS
FULL VEHICLE24–48 HOURS
DIRECT FACTORY DISPATCH · SKU PA-49-UV · 1:1 BY VOL / WEIGHT
POLYASPARTIC 49 — Fast-Cure Topcoat (2-Gal Kit)
$229 – $965Batch-matched TDS included · Freight quoted at checkout
KIT SIZE & YIELD2-Gal Metal F-Tin Kit (1A:1B)Covers ~450 sq ft / kit
CONTAINER FORMAT1-Gal Metal F-Tins (5.5"×6.5") & 5-Gal PailsUN-rated jobsite packaging
KIT CONTENTS1 Gal Part A (Resin) + 1 Gal Part B (Activator)Pre-proportioned factory fill
MIX RATIO (A : B)1:1 BY VOL / WEIGHT (1 PART A : 1 PART B)350 RPM spiral paddle · 2–3 min
Restocking Soon — Request Priority Allocation / LTL Quote →
Strict on-hand policy: 0-stock & 5-Gal LTL items reserve directly on our Houston 77008 Priority Allocation Pad (unlocks PRO15 / CREW20 / PALLET25).
ASTM Technical Data Sheet (PDF) ↓Kit SDS (PDF) ↓Part A SDS ↓Part B SDS ↓Part A Label PDF ↓Part B Label PDF ↓Calculate kits for your sq ft →
Ultra-fast curing aliphatic polyaspartic topcoat with superior UV stability, scratch resistance, and chemical resistance.
VISUAL ENGINEERING BREAKDOWN · 2000×2000 HIGH-CONTRAST PLATES
Stoichiometry, Film Build, ASTM Lab Proof & 5-Stage Slab Architecture
PT03 · FILM BUILD
32–40 Mil 100% Solids vs. 2–3 Mil Water-Based Paint
Zero evaporation shrinkage vs. 50% carrier loss in box-store garage kits that peel under hot tires.
PT04 · ASTM LAB PROOF
11,500+ PSI Compressive & 25 lbs MVER Defense
Verified ASTM D695 compressive load, Shore D 82–85 hardness, Taber <25 mg wear, and 2,000+ hr QUV non-yellowing.
PT05 · 5-STAGE ARCHITECTURE
Cross-Section Slab Cutaway (CSP 2–3 to Polyaspartic)
Monolithic bond from diamond-ground concrete through Primer/MVB 49, Epoxy 49 + Mica/Flake, and Polyaspartic 49.
300 DPI PRESS ARTWORK & CONTAINER VERIFICATION
Packaging Label & Container Preview
1080P FIELD APPLICATION & CURED FINISH
Live Pour & Showroom Performance
POLYASPARTIC 49 · LIVE APPLICATION
POLYASPARTIC 49 Jobsite Mixing & Pour Execution
CLEAR TOPCOAT (99% SOLIDS) | RAPID RETURN TO SERVICE
CURED COMMERCIAL FINISH
3-Car Showroom Mirror-Gloss Floor
Shore D 82–85 cured armor rated >11,500 psi compressive strength and hot-tire immune to 140°F.
| Solids Content | 98% – 99% (D2697) |
|---|---|
| Mix Ratio (A:B) | 1:1 by Vol or Weight |
| Mixed Viscosity | 400 – 600 cps |
| Pot Life (72°F, 50% RH) | 15 – 20 Minutes |
| Shore D Hardness | 80 – 82 D (D2240) |
| Taber Abrasion | <25 mg (CS-17, 1k cyc) |
| UV Stability (QUV) | 2,000+ Hrs (No Yellow) |
| Hot-Tire Defense | Unaffected @ 140°F |
| Tensile Strength | 6,500 psi (D638) |
| VOC Content | <50 g/L (SCAQMD 1113) |
| Specific Gravity | A: 1.07 | B: 1.07 |
| Dry to Touch Time | 2 Hours @ 72°F |
| Light Foot Traffic | 4 – 6 Hours @ 72°F |
| Full Return to Service | 24 – 48 Hours @ 72°F |
- 01Substrate Readiness: Base coat must be tack-free. If epoxy cured >24 hrs, abrade with 120-grit screen.
- 02Dew Point Check: Substrate temperature must be at least 5°F (3°C) above the calculated dew point.
- 03Mix Ratio: Accurately combine 1 Part A to 1 Part B by volume or weight in a clean container.
- 04Mechanical Mix: Blend 2 minutes with spiral paddle at 350 RPM. Do NOT aerate or whip micro-bubbles.
- 05Rapid Working Time: Working time is 15-20 min. Higher humidity significantly accelerates curing speed!
- 06Immediate Placement: Pour ribbon immediately onto floor. Pull with flat squeegee or magic trowel.
- 07Cross-Rolling: Immediately back-roll in both directions with 18" 3/8" nap lint-free roller.
- 08Smooth Topcoat: 200–250 sq. ft./gal (400–500 sq. ft. per 2-gal kit) applied at 6-8 wet mils.
- 09Flake Grout Coat: 125-160 sq. ft./gal (250–320 sq. ft. per 2-gal kit) applied at 10-12 wet mils.
- 10Thickness Limit: Never apply >12 wet mils per coat. Over-application causes solvent/moisture haze.
IRRITANT
HEALTH HAZARD
- H317: May cause an allergic skin reaction.
- H319: Causes serious eye irritation.
- H332: Harmful if inhaled (Aliphatic Polyisocyanate Prepolymer).
- H334: May cause allergy or asthma symptoms if inhaled.
- H335: May cause respiratory irritation.
MANDATORY APPLICATOR PPE
Nitrile Gloves8+ mil chemical resistant
Splash GogglesANSI Z87.1 eye protection
OV RespiratorNIOSH organic vapor cartridge
Spiked FootwearLong sleeves & 3/4" spikes
24-HR CHEMTREC EMERGENCY:1-800-424-9300